Passive House Design: The Core Principles Explained

passive house design principles

Trying to work out what makes a home Passive House? You can boil the passive house design principles down to five linked ideas: superinsulation, no thermal bridges, airtightness, good windows and heat-recovery ventilation.

If you want wider context first, the architecture basics guide covers the field as a whole.

Item Value
Space heating demand ≤15 kWh/m²a
Alternative peak heating load ≤10 W/m²
Airtightness ≤0.6 ACH50
Window U-value (whole unit) 0.80 W/(m²K) or better
Thermal comfort No more than 10% of hours above 25°C

These figures come from an October 2025 certification guide and the NSW Planning Portal, whose page was last updated 09/03/2026. Figures can change, so check the sources before you rely on them.

The five principles at a glance

Passive House, or Passivhaus, is a performance-based standard that originated in Germany, according to the NSW Planning Portal. A 2009 GreenBuildingAdvisor article says the concept was developed by Dr Wolfgang Feist and Prof. Bo Adamson in the late 1980s.

The certification guide describes five interdependent principles:

  1. Superinsulation of walls, roof and floor.
  2. Thermal-bridge-free design.
  3. Airtight construction.
  4. High-performance windows.
  5. Mechanical ventilation with heat recovery.

The same guide stresses that these interact. Neglect one and the others have to work harder to make up for it.

Superinsulation and thermal bridges

A continuous layer of superinsulation wraps the whole envelope. For cool-temperate climates such as Central Europe, the certification guide says this typically means U-values of 0.14 W/(m²K) or better for opaque elements, roughly double or triple the insulation current building codes require.

In imperial units, a 2015 Construction Specifier article puts most envelope requirements at R-40 to R-60 for walls. It notes that such walls can be much thicker, which is why continuous-insulation systems are often used to keep them slimmer.

A thermal bridge forms where a conductive material bypasses the insulation. The usual culprits are:

  • Steel beams.
  • Concrete balconies.
  • Window frames.

The guide quotes Passive House Institute guidance that all edges, corners, connections and penetrations must be planned and executed with great care so bridges are avoided. Designers therefore detail every junction rather than simply adding thicker insulation.

Airtightness and ventilation

Passive House requires airtightness of no more than 0.6 air changes per hour at 50 Pascals (ACH50), proved by an onsite blower door test, as the NSW Planning Portal explains. The certification guide says a typical code-minimum new home might reach 3-5 ACH50, so the Passive House threshold is approximately 5-8x tighter.

Sealed does not mean stuffy. The same guide points out that airtightness is not the same as ventilation: the house is sealed so that air enters and leaves only where you intend, with mechanical ventilation supplying fresh air.

passive house design principles LED lighting
A clear LED bulb and a white electrical plug rest on a dark wooden surface.

The name is a little misleading. The GreenBuildingAdvisor article notes that all Passivhauses must have an active mechanical ventilation system and some type of active heating system, albeit very small ones.

The heat recovery step is what saves energy. In winter, the unit recovers a portion of the heat that would otherwise be exhausted, according to the Construction Specifier, which says such systems should run at about 90 percent efficiency. The certification guide sets the minimum at ≥75%, so sources describe the target differently.

High-performance windows and solar gain

Windows are typically the weakest thermal point in an envelope. The certification guide says Passive House requires triple-glazed windows with insulated frames, low-emissivity coatings and argon or krypton gas fill, aiming for 0.80 W/(m²K) or better for the whole window unit.

The Construction Specifier adds that the window figure is a recommendation, not a requirement. If you specify weaker windows, the envelope insulation must compensate.

Orientation matters too. The same guide says solar heat gain lets winter sun provide free heating while the design limits summer overheating, though the GreenBuildingAdvisor article says passive solar design is recommended but not mandatory.

How is a Passive House certified?

The Passive House Institute (PHI) administers an international scheme carried out by a PHI-approved certifier, per the NSW Planning Portal. As of the guide’s October 2025 date, there are three certification classes, Classic, Plus and Premium, which differ in their renewable energy requirements, according to the certification guide.

The standard is defined by measurable benchmarks. According to the NSW Planning Portal, it sets stringent benchmarks for thermal performance, covering:

  • Heating demand and/or heating load.
  • Cooling and dehumidification demand.
  • Air tightness.
  • Primary energy demand for all energy consumption.

Meeting those benchmarks takes a familiar package: high levels of insulation, minimal thermal bridges, very good air tightness, high-performance windows and doors, and mechanical ventilation with heat recovery (MVHR), as the NSW page puts it. The certification guide calls the result pass/fail, quoting PHI that a certificate is issued only if the precisely defined criteria are met without exception.

Comfort is part of the test. The same guide lists thermal comfort with no more than 10% of hours above 25°C, and verification through PHPP modeling plus on-site blower door testing.

In New South Wales, Australia, the BASIX route has these steps:

  1. Engage a certified Passive House designer or certifier, who verifies the design with the Passive House Planning Package (PHPP).
  2. Attach the PHPP software report to the BASIX certificate.
  3. After construction, have a registered tester run a blower door test showing no more than 0.6 ACH50.

Paperwork continues beyond design. The verification section of the PHPP report must show that the dwelling satisfies the space heating, space cooling and air tightness requirements, and the designer or certifier must give a written endorsement that the plans and documentation were assessed in accordance with the standard. A certified Passive House also goes through quality assurance to ensure it is built as designed, per the NSW Planning Portal.

As of the NSW page last updated 09/03/2026, this standard method is only available in certain locations in NSW. The page also notes that Passive House assessments do not directly correlate with outcomes from the simulation method using NatHERS accredited software, and that the Australian Passive House Association can help you locate a certified designer.

Limits and criticisms

The standard has critics. In 2009, John Straube argued that many recommendations were not likely good decisions for cold-climate (DOE Climate Zones 5-7) North American housing. That is one author’s opinion from an older article, so weigh it against newer guidance.

Passive House is one approach within the wider field of sustainable architecture principles. It is also a performance standard rather than a style; for how design thinking shifted over time, see the famous architects of the 20th century.

Frequently asked questions

Is a Passive House really passive?

Show answer

Not entirely. The GreenBuildingAdvisor article says all Passivhauses must have an active mechanical ventilation system and some type of small active heating system.

How airtight does a Passive House have to be?

Show answer

No more than 0.6 ACH50, according to the NSW Planning Portal. The Construction Specifier adds that PHI’s EnerPHit retrofit standard requires a more achievable 1.0 ACH50.

What are the certification classes?

Show answer

Classic, Plus and Premium. The NSW Planning Portal says Plus and Premium also require renewable energy generation.

When should airtightness be tested?

Show answer

The Construction Specifier says an early blower door test helps show where extra air sealing is needed. A final test follows once the envelope and mechanical systems are complete.